NOTICE: For detailed instructions please view the Magicycle Deer assembly video.

NOTICE: The following assembly steps are only a general guide to assist in the assembly of your Magicycle Commuter and is not a complete or comprehensive manual of all aspects of assembly, maintenance and repair. We recommend you consult a certified bicycle mechanic to assist in the assembly, repair and maintenance of your bicycle. For detailed instructions please view the Magicycle Jaguarundi assembly video.

Step 1: Install the front wheel. Remove the plastic fork guard lever from the fork, making sure not to touch the brake caliper set. Put the front wheel into the fork and make sure the front wheel hub goes into the fork dropout and the brake disc goes into the caliper, next align the fork tines with the axle of the hub to make sure the fork tines are fully seated on the axle. Unscrew the quick-release nut and conical spring to install the quick-release lever from the left side of the wheel, then insert the quick-release lever into the front wheel hub, keeping the two conical springs pointing towards the hub, tighten the quick-release nut until the quick-release lever and The outside of the quick release nut is flush, make sure that the front wheel axle is completely placed on the bottom of the slot of the front fork dropout, and then firmly tighten the quick release handle upwards.

Step 2: Install the front fender, clamp the nut with a socket wrench, loosen the screw with an Allen wrench and remove the screw. The mounting screws pass through the front fender bracket and use an Allen key to fix the screws of the front fender and the front fender bracket.

Step 3:Install the handle. Remove the 4 cover plate locking screws from the seat tube, make sure that the center drum knurl on the handlebar is in the middle of the seat tube, and adjust the handlebar to a comfortable position. Finally, tighten the screws with the assembly tool.

Step 4: Install the pedals. The left and right pedals are marked L left R right on both ends. First, install the right pedal by tightening the pedal inclockwise direction. The left pedal is tightened by turning the pedal in counterclockwise direction. Both pedals should be tightened to 35 Newton meters by using a torque wrench.

Step 5: Use a bike pump with a press gauge to inflate tires to desired KPA.

Step 6: Adjust the saddle height. Loosen the seat tube clip with an Allen key, remove the seat tube and make sure the at clip is centered on the hole on this at tube. Insert the seat tube into the middle tube of the frame, adjust the saddle height to a suitable height, (be careful not to leak the safety wire on the seat tube) and tighten the adjustment nut.

NOTICE: The following assembly steps are only a general guide to assist in the assembly of your Magicycle Bike and are not a complete or comprehensive manual of all aspects of assembly, maintenance, and repair. We recommend you consult a certified bicycle mechanic to assist in the assembly, repair, and maintenance of your ebike. For detailed instructions please view the Magicycle Jaguarundi assembly video.

Step 1: Install the front wheel. Remove the plastic fork guard lever from the fork, making sure not to touch the brake caliper set. Put the front wheel into the front fork and make sure that the front wheel hub goes into the fork dropout, the brake disc goes into the caliper, and unscrew the quick release nut and conical spring to install the quick release lever from the left side of the wheel, then put the quick release lever Insert the front wheel hub, keeping the two conical springs pointing towards the hub, tighten the quick release nut until the quick release lever is flush with the outside of the quick release nut, make sure the front wheel hub is fully seated on the bottom of the fork dropout slot without a gap, then lock the quick release handle upwards.

Step 2: Install the front fender, clamp the nut with a socket wrench, loosen the screw with an Allen wrench, and remove the screw. The mounting screws pass through the front fender bracket and use an Allen key to fix the screws of the front fender and the front fender bracket.

Step 3: Install the handle. Remove the 4 cover plate locking screws from the seat tube, make sure that the center drum knurl on the handlebar is in the middle of the seat tube, and adjust the handlebar to a comfortable position. Finally, tighten the screws with the assembly tool.

Step 4: Install the pedals. The left and right pedals are marked L left R right on both ends. First, install the right pedal by tightening the pedals clockwise, and tightening the left pedal by turning the pedals counterclockwise. Both pedals should be tightened to 35 Nm using a torque wrench.

Step 5: Use a bike pump with a press gauge to inflate tires to the desired KPA.

Step 6: Adjust the saddle height. Loosen the seat tube clip with an Allen key, remove the seat tube and make sure the clip is centered on the hole on this tube. Insert the seat tube into the middle tube of the frame, adjust the saddle height to a suitable height, (be careful not to leak the safety wire on the seat tube) and tighten the adjustment nut.

NOTICE: The following assembly steps are only a general guide to assist in the assembly of your Magicycle Bike and is not a complete or comprehensive manual of all aspects of assembly, maintenance and repair. We recommend you consult a certified bicycle mechanic to assist in the assembly, repair and maintenance of your bicycle. For detailed instructions please view the Magicycle Ocelot/ Ocelot Pro Assembly video.

Step 1: Install the front wheel. Remove the plastic fork guard lever from the fork, making sure not to touch the brake caliper set. Put the front wheel into the front fork and make sure that the front wheel hub goes into the fork dropout, the brake disc goes into the caliper, and unscrew the quick release nut and conical spring to install the quick release lever from the left side of the wheel, then put the quick release lever Insert the front wheel hub, keeping the two conical springs pointing towards the hub, tighten the quick release nut until the quick release lever is flush with the outside of the quick release nut, make sure the front wheel hub is fully seated on the bottom of the fork dropout slot without a gap, then lock the quick release handle upwards.

Step 2: Install the front fender, clamp the nut with a socket wrench, loosen the screw with an Allen wrench, and remove the screw. The mounting screws pass through the front fender bracket and use an Allen key to fix the screws of the front fender and the front fender bracket.

Step 3: Install the handle. Remove the 4 cover plate locking screws from the seat tube, make sure that the center drum knurl on the handlebar is  in the middle of the seat tube, and adjust the handlebar to a comfortable position. Finally, tighten the screws with the assembly tool.

Step 4: Install the pedals. The left and right pedals are marked L left R right on both ends. First, install the right pedal by tightening the pedals clockwise, and tightening the left pedal by turning the pedals counterclockwise. Both pedals should be tightened to 35 Nm using a torque wrench.

Step 5: Use a bike pump with a press gauge to inflate tires to the desired KPA.

Step 6: Adjust the saddle height. Loosen the seat tube clip with an Allen key, remove the seat tube and make sure the clip is centered on the hole on this tube. Insert the seat tube into the middle tube of the frame, adjust the saddle height to a suitable height, (be careful not to leak the safety wire on the seat tube) and tighten the adjustment nut.

NOTICE: Ensure all hardware is tightened properly and all safety checks in the following sections are performed before first use. Contact Magicycle Bike if you have any questions regarding the assembly of your bike. If you are not able to ensure all the assembly steps in the assembly video are performed properly, or you are unable to view the assembly video please consult a certified local bicycle service provider for assistance in addition to contacting Magicycle Bike After-Service for help.

NOTICE: The following assembly steps are only a general guide to assist in the assembly of your Magicycle Bike and is not a complete or comprehensive manual of all aspects of assembly, maintenance and repair. We recommend you consult a certified bicycle mechanic to assist in the assembly, repair and maintenance of your bicycle. For detailed instructions please view the Magicycle Cruiser/ Cruiser Step-thru Assembly video.

Step 1: Install the handlebars. Remove the four screws from the stem, ensuring the linear markings on the handlebars are centered and handlebars are adjusted to the comfortable position. Finally, tighten the screws with the assembly tool.

Step 2: Install the headlight. Use a socket wrench to hold the nut and loosen the screw with a inner hexagon wrench and remove the screw. Install the screw pass through headlight and the bracket and adjust the headlight properly for riding conditions.

Step 3: Install the front fender, clamp the nut with a socket wrench, loosen the screw with an Allen wrench and remove the screw. The mounting screws pass through the headlight bracket and the front fender bracket, and use an Allen key to fix the screws of the front fender and the front fender bracket.

Step 4: Install the front wheel. Remove the plastic front fork guards from the front wheel being sure not to touch the brake rotor set. Open the quick skewer and remove the thumb nut and cone spring. Carefully lower the fork and ensure the brake rotor goes into the caliper. Next align the dropouts with the axle of the wheel hub to make sure the fork dropouts are fully seated on the axle. Install the quick skewer starting from the brake rotor side of the wheel and then push quick release skewer through the hub. Keep two cone springs pointed towards the wheel hub. Tighten the thumb nut until the quick release lever is held in line with the axle, and then use your palm of your hand to close the quick release skewer.

Step 5: Use a bike pump with a press gauge to inflate tires to desired KPA. The recommended pressure for this mode is 40 KPA. Do not over inflate or underinflate tires.

Step 6: Install the pedals. The left and right pedals are marked on both ends. First, install the right pedal by tightening the pedal in clockwise direction. The left pedal is tightened by turning the pedal in counterclockwise direction. Both pedals should be tightened to 35 Newton meters by using a torque wrench.

Step 7: Adjust the saddle height loosen the seat clamp, remove the seat post and ensure the seat clamp is centered over the hole in the seat tube. Insert the seat post into the slot, adjust the saddle height to a suitable height and tighten the adjustment nut When you feel resistance, close the seat tube clamp fully.

Step 8: Adjust the seat position forwards or backwards. Use a alien wrench to loosen the seat adjustment bolt and make sure to stay within the marked adjustment range.

Step 9: Check whether the battery pack is locked into the frame of the Magicycle Cruiser / Cruiser Step-thru When you want to take off the battery insert the key and turn to release the battery pack. The battery pack can be removed and charged separately. This is the charging port. Align the battery pack to the battery holder carefully and push until when you hear it click into the place.

NOTICE: Ensure all hardware is tightened properly and all safety checks in the following sections are performed before first use. Contact Magicycle Bike if you have any questions regarding the assembly of your bike. If you are not able to ensure all the assembly steps in the assembly video are performed properly, or you are unable to view the assembly video please consult a certified local bicycle service provider for assistance in addition to contacting Magicycle Bike After-Service for help.